#Remote wake up bios software#
#Remote wake up bios mac#

Click OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Specify the external port and internal port as 7, which is used to receive Magic Packets. Quick note: The device you want to wake up remotely has to be turned on for the tool to find it. Specify the WAN port according to the network environment. Click the Play (Start Scanning) button to discover all the devices in the network. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page.

#Remote wake up bios mac#

Enter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Check if the desired IP address is reserved for PC A. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. Enable Export to DHCP Address Reservation. Your computer need to be configured before use. Note : This application use the WakeOnWan / WakeOnLan protocol (WOW / WOL). Simply type the required information (IP, Port, MAC Address), and you're done You can store information about your most used computers for faster use. In the IP-MAC Binding List section, click to load the following page. Wake your computer from a remote location using this application. To do this, open the software that we installed at Step 4 (Wake-up-LAN), type the MAC Adress and the IP Adress into the two boxes and hit Wake up PC. During the computers power-on self-test enter the BIOS setting screen by pressing the F1, INS, or DEL keys 2. Now that we managed to configure everything, your computer is ready to be woken up at all times. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Step 5: Waking the Computer with Wake-on-Lan. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router. Make sure the WAN port of the router is routable from PC B.PC A should be powered off normally and the power supply is normal.In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet. Make sure that the network card of PC A supports WOL.In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN. Make sure that the motherboard of PC A supports WOL.It is required that PC B can wake up PC A by sending a Magic Packet via the internet.īefore configuring WOL, you should do the following preparation: In the diagram below, PC A is connected to the internet via the router. To Enable Wake on LAN go to Settings > Unattended Access > Wake on LAN.You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet.

You may enable wake on LAN on the remote computer from our website itself. Make sure you have enabled wake on LAN on the remote computer.

Under Wake on LAN/WLAN, choose 'LAN or WLAN'.

During the computer's power-on self-test, enter the BIOS setting screen by pressing the F1, INS, or DEL keys.

The most common method adopted across different vendors is as follows. You need to enable it on each unattended computer for Wake on LAN to work. The Wake on LAN is generally disabled in the BIOS settings.

A minimum of one computer with unattended agent installed should be online in the target network.

The remote computer should be connected to the power source.

The remote computer you are trying to turn on should be on wired (Ethernet) network connection (not Wi-Fi).

You will be able to use Wake On LAN to switch on a computer that is in sleep /hibernate/shutdown if all the below requirements are met. Why am I not able to wake the remote computer?